NMi Fire Fly fxpig (tarafından spoon)
| Kazanma : | +25.27% |
| Düşüş | 25.32% |
| Pipler: | 692.8 |
| Tradeler | 441 |
| Kazandı: |
|
| Kaybetti: |
|
| Tür: | Gerçek |
| Kaldıraç: | 1:500 |
| Trading: | Otomatik |
NMi Fire Fly fxpig Tartışma
Mar 27, 2012 at 11:50
1,235 Görüntüleme
9 Replies
Dec 07, 2009 zamanından beri üye
134 iletiler
May 24, 2012 at 13:28
Can you turn on the comments for the trades so that we can tell which EA is trading.
Be afraid, very afraid?
Nov 16, 2011 zamanından beri üye
9 iletiler
May 24, 2012 at 14:20
I think the comments are on, it says so in the settings, only the last few trades will show up as comments have been enabled over the last few days
Dec 07, 2009 zamanından beri üye
134 iletiler
May 24, 2012 at 14:47
If it is not working correctly then you might just try the publishing EA and the new beta add account link in the yellow band on the 'Add Account' page. It is very quick and very simple and works without problems like the old manual set up.
Be afraid, very afraid?
forex_trader_1363
Oct 03, 2009 zamanından beri üye
27 iletiler
May 28, 2012 at 16:22
thanks for sharing spoon -can you please confirm which vps and set up ( RAM etc) you are using?
thanks,
Peter
thanks,
Peter
Nov 16, 2011 zamanından beri üye
9 iletiler
May 28, 2012 at 21:16
hey, it softlayer, 2 gb ram.
also, i can not turn comments on as i thinik i need the myfxbook ea set up, i think1
also, i can not turn comments on as i thinik i need the myfxbook ea set up, i think1
Feb 09, 2011 zamanından beri üye
320 iletiler
Jun 14, 2012 at 11:11
Hello spoon, what is Your avg. open slip and avg. close slip using softlayer+fxpig ECN account? Also what exec times do You get there ?
Better to lose an oportunity than a money
Nov 16, 2011 zamanından beri üye
9 iletiler
Jun 14, 2012 at 11:31
Hey,
Most prob the easiest way to answer that is from MDP screen capture.....
My softlayer is only 1 core at the moment and also still in dallas, although i hope to increase the power but i think i shall still say at dallas for the time being to see trade differences between adams trades and my own.
Did i read your going to run Number 1 at fxpig?? if so, once its done a little trading lets me know how its going please :)
Most prob the easiest way to answer that is from MDP screen capture.....
My softlayer is only 1 core at the moment and also still in dallas, although i hope to increase the power but i think i shall still say at dallas for the time being to see trade differences between adams trades and my own.
Did i read your going to run Number 1 at fxpig?? if so, once its done a little trading lets me know how its going please :)
Ekler :
Feb 09, 2011 zamanından beri üye
320 iletiler
Jun 14, 2012 at 13:27
AFAIK main data center of FxPig is in Dalls, I must say Your slippage is very nice, however exec times are a little bit high I must say, I usually accept only speeds below 600ms and Your avg.open time = 1067ms which is quiet big. Try to reset Your stats and do a measure again ,maybe one trade with a very long time screw up the average.
No I do now own NO1 or NMi, I only use MDP and my own EAs.
Thanks for sharing!
No I do now own NO1 or NMi, I only use MDP and my own EAs.
Thanks for sharing!
Better to lose an oportunity than a money
Nov 16, 2011 zamanından beri üye
9 iletiler
Jun 14, 2012 at 13:51
To be honest that's the longest I have seen the exec times, but hey ste usually not as low at 600. If you remind me after the next MDP trade(s) I'll do another screen capture for you. Also they have a data centre in Washington which fxpig is the better one to go with, but I shall stick to Dallas it's it's been good so far.
Nov 16, 2011 zamanından beri üye
9 iletiler
Aug 14, 2012 at 14:19
This accoount will not be trading any more.....funds headding to axi and a new amarda account....links to follow....
*Ticari kullanım ve istenmeyen e-postalara müsamaha gösterilmez ve hesabın feshedilmesine neden olabilir.
İpucu: Bir resim/youtube urlsi yayınlamak, onu otomatik olarak gönderinize gömer!
İpucu: Bu tartışmaya katılan bir kullanıcı adını otomatik olarak tamamlamak için @ işaretini yazın.
